3949247 Lid Switch for Whirlpool

Use ctrl+F then enter your model number in search bar and hit enter

Installation Instructions for 3949247

1. Unplug appliance and/or turn off circuit breakers to prevent electrocution.
2. Firstly, remove control panel of the appliance using a screwdriver. Slide it slightly forward and then lift over the machine.
3. Next, disconnect the lid switch and remove the two retaining cliff switches with a flat head screwdriver.
4. Next, remove the body from the washer by lifting the lid, putting a foot against the body of machine and lifting the machine at a 45-degree angle.
5. Then, remove the electrical connectors of the body. Press tabs in, then down with a flat head screwdriver.
6. Unscrew the lid switch located underneath the lid. To change the lid switch, the machine must be laying down on its’ front, to protect the machine place a towel on the floor and place the body of the machine on the floor.
7. With a 5/16^th snot, remove the ground wire, and with a small flat head screwdriver pry up the clips holding the harness and wires in.
8. With a flat head screwdriver, pry out the clips, place the wire harness and reinstall the ground wire. Place the wire harness back into frame hole.
9. Lift the machine’s body to grab the switch, lift switch, line up the holes located underneath the lid and place in screws.
10. Next is placing the body back into the machine. Lift the lid, grab the lid with one hand, with the other grab the machine, place a foot on the bottom of the machine, tilt at a 45-degree angle, and place into the machine.
11. Make sure it locks in into the four tabs. Hook the clips back into the back panel and with flat head screwdriver push them in. reconnect the lid switch. Lift over console push it back slightly and place screws back in.
12. Plug in appliance.

Tools Needed:

• Screwdriver
• Flat head screwdriver
• 5/16^th snot

Description

• Cross Reference Information
  394924, AP3100003, 3949237, 3949239, 3949240, 547225, AH350434, EA350434, PS350434
• Quality you can Trust! All Snap Products are made with premium materials and are tested so they last.
• Click here for installation instructions!
• Compatible with the following Washer brands:  Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef

Use ctrl+F then enter your model number in search bar and hit enter

Installation Instructions for 3949247

1. Unplug appliance and/or turn off circuit breakers to prevent electrocution.
2. Firstly, remove control panel of the appliance using a screwdriver. Slide it slightly forward and then lift over the machine.
3. Next, disconnect the lid switch and remove the two retaining cliff switches with a flat head screwdriver.
4. Next, remove the body from the washer by lifting the lid, putting a foot against the body of machine and lifting the machine at a 45-degree angle.
5. Then, remove the electrical connectors of the body. Press tabs in, then down with a flat head screwdriver.
6. Unscrew the lid switch located underneath the lid. To change the lid switch, the machine must be laying down on its’ front, to protect the machine place a towel on the floor and place the body of the machine on the floor.
7. With a 5/16^th snot, remove the ground wire, and with a small flat head screwdriver pry up the clips holding the harness and wires in.
8. With a flat head screwdriver, pry out the clips, place the wire harness and reinstall the ground wire. Place the wire harness back into frame hole.
9. Lift the machine’s body to grab the switch, lift switch, line up the holes located underneath the lid and place in screws.
10. Next is placing the body back into the machine. Lift the lid, grab the lid with one hand, with the other grab the machine, place a foot on the bottom of the machine, tilt at a 45-degree angle, and place into the machine.
11. Make sure it locks in into the four tabs. Hook the clips back into the back panel and with flat head screwdriver push them in. reconnect the lid switch. Lift over console push it back slightly and place screws back in.
12. Plug in appliance.

Tools Needed:

• Screwdriver
• Flat head screwdriver
• 5/16^th snot

Snap Supply now offers wholesale.
Sign in 

Sign up

Items bought from Snap Supply can be returned within 30 days of receipt of shipment. Alterations to Snap Supply products is a violation of the return policy and will result in a nonrefundable product. To ensure your satisfaction with our products please contact us with any questions.

Click here for more about our Return Policy

Shipping can be expensive, that is why Snap Supply provides free shipping on all orders! No minimum order amounts, that force you to buy something you don't need. Order before 1 PM Eastern and it will ship that same day!

Buy with Confidence! Snap Supply Parts always come with a 1 Year Warranty.

Click here to learn more about our Warranty Policy